1.100ASK-V853-PRO编译烧写

book@100ask:~/workspaces$ cat tina-v853-open.tar.gz* | tar xz

book@100ask:~/workspaces$ ls
tina-v853-open            tina-v853-open.tar.gz.01  tina-v853-open.tar.gz.03  tina-v853-open.tar.gz.05  tina-v853-open.tar.gz.07  tina-v853-open.tar.gz.09  tina-v853-open.tar.gz.11
tina-v853-open.tar.gz.00  tina-v853-open.tar.gz.02  tina-v853-open.tar.gz.04  tina-v853-open.tar.gz.06  tina-v853-open.tar.gz.08  tina-v853-open.tar.gz.10

book@100ask:~/workspaces$ git clone https://github.com/DongshanPI/100ASK_V853-PRO_TinaSDK.git
Cloning into '100ASK_V853-PRO_TinaSDK'...
remote: Enumerating objects: 14606, done.
remote: Counting objects: 100% (232/232), done.
remote: Compressing objects: 100% (167/167), done.
remote: Total 14606 (delta 39), reused 225 (delta 34), pack-reused 14374
Receiving objects: 100% (14606/14606), 883.22 MiB | 4.26 MiB/s, done.
Resolving deltas: 100% (1491/1491), done.
Checking out files: 100% (11560/11560), done.

book@100ask:~/workspaces$ cp -rfvd 100ASK_V853-PRO_TinaSDK/* tina-v853-open/

book@100ask:~/workspaces$ cd tina-v853-open/
book@100ask:~/workspaces/tina-v853-open$ ls
brandy  build  buildroot  build.sh  device  kernel  openwrt  platform  prebuilt  tools

book@100ask:~/workspaces/tina-v853-open$ source build/envsetup.sh
NOTE: The SDK(/home/book/workspaces/tina-v853-open) was successfully loaded
load openwrt... ok
Please run lunch next for openwrt.
load buildroot,bsp...ok
Please run ./build.sh config next for buildroot,bsp.

book@100ask:~/workspaces/tina-v853-open$ lunch

You're building on Linux

Lunch menu... pick a combo:
     1  v853-100ask-tina
     2  v853-vision-tina
Which would you like?:

book@100ask:~/workspaces/tina-v853-open$ lunch

You're building on Linux

Lunch menu... pick a combo:
     1  v853-100ask-tina
     2  v853-vision-tina
Which would you like?: 1
Jump to longan autoconfig
/home/book/workspaces/tina-v853-open/build.sh autoconfig -o openwrt -i v853 -b 100ask           -n default

Before using this files, please make sure that you note the following important information.
**********************************************************************

Copyright (c) 2019-2022 Allwinner Technology Co., Ltd. ALL rights reserved.

Allwinner is a trademark of Allwinner Technology Co.,Ltd., registered in
the the People's Republic of China and other countries.
All Allwinner Technology Co.,Ltd. trademarks are used with permission.

DISCLAIMER
THIRD PARTY LICENCES MAY BE REQUIRED TO IMPLEMENT THE SOLUTION/PRODUCT.
IF YOU NEED TO INTEGRATE THIRD PARTY'S TECHNOLOGY (SONY, DTS, DOLBY, AVS OR MPEGLA, ETC.)
IN ALLWINNERS'SDK OR PRODUCTS, YOU SHALL BE SOLELY RESPONSIBLE TO OBTAIN
ALL APPROPRIATELY REQUIRED THIRD PARTY LICENCES.
ALLWINNER SHALL HAVE NO WARRANTY, INDEMNITY OR OTHER OBLIGATIONS WITH RESPECT TO MATTERS
COVERED UNDER ANY REQUIRED THIRD PARTY LICENSE.
YOU ARE SOLELY RESPONSIBLE FOR YOUR USAGE OF THIRD PARTY'S TECHNOLOGY.


THIS SOFTWARE IS PROVIDED BY ALLWINNER"AS IS" AND TO THE MAXIMUM EXTENT
PERMITTED BY LAW, ALLWINNER EXPRESSLY DISCLAIMS ALL WARRANTIES OF ANY KIND,
WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING WITHOUT LIMITATION REGARDING
THE TITLE, NON-INFRINGEMENT, ACCURACY, CONDITION, COMPLETENESS, PERFORMANCE
OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
IN NO EVENT SHALL ALLWINNER BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS, OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
OF THE POSSIBILITY OF SUCH DAMAGE.

**********************************************************************
You can read /home/book/workspaces/tina-v853-open/build/disclaimer/Allwinnertech_Disclaimer(Cn_En)_20181122.md for detailed information.

You read time left 8 seconds....
I have already read, understood and accepted the above terms? [Y/N]y

You select Yes, Build continue....
========ACTION List: mk_autoconfig -o openwrt -i v853 -b 100ask -n default;========
options :
INFO: Prepare toolchain ...
INFO: kernel defconfig: generate /home/book/workspaces/tina-v853-open/kernel/linux-4.9/.config by /home/book/workspaces/tina-v853-open/device/config/chips/v853/configs/100ask/linux-4.9/config-4.9
INFO: Prepare toolchain ...
make: Entering directory '/home/book/workspaces/tina-v853-open/kernel/linux-4.9'
  HOSTCC  scripts/basic/fixdep
  HOSTCC  scripts/kconfig/conf.o
  SHIPPED scripts/kconfig/zconf.tab.c
  SHIPPED scripts/kconfig/zconf.lex.c
  SHIPPED scripts/kconfig/zconf.hash.c
  HOSTCC  scripts/kconfig/zconf.tab.o
  HOSTLD  scripts/kconfig/conf
*** Default configuration is based on '../../../../../device/config/chips/v853/configs/100ask/linux-4.9/config-4.9'
#
# configuration written to .config
#
make: Leaving directory '/home/book/workspaces/tina-v853-open/kernel/linux-4.9'
INFO: clean buildserver

Usage:
 kill [options] <pid> [...]

Options:
 <pid> [...]            send signal to every <pid> listed
 -<signal>, -s, --signal <signal>
                        specify the <signal> to be sent
 -l, --list=[<signal>]  list all signal names, or convert one to a name
 -L, --table            list all signal names in a nice table

 -h, --help     display this help and exit
 -V, --version  output version information and exit

For more details see kill(1).
INFO: prepare_buildserver

book@100ask:~/workspaces/tina-v853-open$ make
===There is tina environment.===
 Note: make is the shell functon in envsetup.sh.

== action: openwrt_build, action_args:  ==
========ACTION List: build_linuxdev ;========
options :
INFO: ----------------------------------------
INFO: build linuxdev ...
INFO: chip: sun8iw21p1
INFO: platform: linux
INFO: kernel: linux-4.9
INFO: board: 100ask
INFO: output: /home/book/workspaces/tina-v853-open/out/v853/100ask/openwrt
INFO: ----------------------------------------
INFO: don't build dtbo ...
INFO: build arisc
INFO: build_bootloader: brandy_path= /home/book/workspaces/tina-v853-open/brandy/brandy-2.0
grep: /home/book/workspaces/tina-v853-open/brandy/brandy-2.0/spl/Makefile: No such file or directory
build for sun8iw21p1_defconfig ...
Prepare arm toolchain ...
...//此部分编译输出信息省略
Building kernel
/home/book/workspaces/tina-v853-open/kernel/linux-4.9/output/lib/modules/4.9.191
  CHK     include/config/kernel.release
  CHK     include/generated/uapi/linux/version.h
  CHK     include/generated/utsrelease.h
  CHK     scripts/mod/devicetable-offsets.h
  CHK     include/generated/timeconst.h
  CHK     include/generated/bounds.h
  CHK     include/generated/asm-offsets.h
  CALL    scripts/checksyscalls.sh
  CHK     include/generated/compile.h
  DTC     arch/arm/boot/dts/board.dtb
  Kernel: arch/arm/boot/Image is ready
  Building modules, stage 2.
  MODPOST 27 modules
  Kernel: arch/arm/boot/zImage is ready
  Kernel: arch/arm/boot/uImage is ready
'arch/arm/boot/Image' -> 'output/bImage'
'arch/arm/boot/uImage' -> 'output/uImage'
'arch/arm/boot/zImage' -> 'output/zImage'
Copy rootfs.cpio.gz for arm
Building modules
[GPU]: No GPU type is configured in /home/book/workspaces/tina-v853-open/kernel/linux-4.9/.config.
regenerate rootfs cpio
16149 blocks
16150 blocks
build_ramfs
Copy boot.img to output directory ...
./scripts/build.sh

sun8iw21p1 compile Kernel successful


INFO: ----------------------------------------
INFO: build Tina OK.
INFO: ----------------------------------------

book@100ask:~/workspaces/tina-v853-open$ pack
/home/book/workspaces/tina-v853-open/build/pack -c sun8iw21p1 -i v853 -p openwrt -b 100ask -k linux-4.9 -d uart0 -v none -m normal -w none -n default
INFO: /home/book/workspaces/tina-v853-open/out/v853/common/keys
copying tools file
copying configs file
copying product configs file
...

Dragon execute image.cfg SUCCESS !
----------image is at----------

33M     /home/book/workspaces/tina-v853-open/out/v853/100ask/openwrt/v853_linux_100ask_uart0.img

pack finish

InstallUSBDrv.exe
drvinstaller_IA64.exe
drvinstaller_X86.exe
UsbDriver/          
drvinstaller_X64.exe   
install.bat