实战 | F1060路由模式典型组网配置案例（静态路由）

网络技术联盟站

发布于 2020-05-14 14:04:31

1.7K00

代码可运行

文章被收录于专栏：网络技术联盟站网络技术联盟站

运行总次数：0

代码可运行

组网及说明

组网说明：

本案例采用H3C HCL模拟器的F1060防火墙来模拟防火墙路由模式的典型部署。为了实现PC之间能够相互通信，因此需要分别在R1、R2、FW1采用三层互联，同时FW1采用路由模式，最终实现PC之间能够相互PING通。

配置步骤

1、按照网络拓扑图正确配置IP地址

2、R1、FW1、R2之间采用三层互联

3、R1、FW1、R2之间采用静态路由协议实现互通。

配置关键点

R1：

<H3C>sys

System View: return to User View with Ctrl+Z.

[H3C]sysname R1

[R1]int gi 0/0

[R1-GigabitEthernet0/0]ip address 192.168.1.1 24

[R1-GigabitEthernet0/0]quit

[R1]int gi 0/1

[R1-GigabitEthernet0/1]des <connect to FW1>

[R1-GigabitEthernet0/1]ip address 10.0.0.1 30

[R1-GigabitEthernet0/1]quit

[R1]int loopback 0

[R1-LoopBack0]ip address 1.1.1.1 32

[R1-LoopBack0]quit

[R1]ip route-static 0.0.0.0 0.0.0.0 10.0.0.2

R2：

<H3C>sys

System View: return to User View with Ctrl+Z.

[H3C]sysname R2

[R2]int gi 0/0

[R2-GigabitEthernet0/0]ip address 172.16.1.1 24

[R2-GigabitEthernet0/0]quit

[R2]int gi 0/1

[R2-GigabitEthernet0/1]des <connect to FW1>

[R2-GigabitEthernet0/1]ip address 10.0.0.5 30

[R2-GigabitEthernet0/1]quit

[R2]int loopback 0

[R2-LoopBack0]ip address 3.3.3.3 32

[R2-LoopBack0]quit

[R2]ip route-static 0.0.0.0 0.0.0.0 10.0.0.6

FW1：

<H3C>sys

System View: return to User View with Ctrl+Z.

[H3C]sysname FW1

[FW1]acl basic 2002

[FW1-acl-ipv4-basic-2002]rule 0 permit source any

[FW1-acl-ipv4-basic-2002]quit

[FW1]

[FW1]zone-pair security source trust destination untrust

[FW1-zone-pair-security-Trust-Untrust]packet-filter 2002

[FW1-zone-pair-security-Trust-Untrust]quit

[FW1]

[FW1]zone-pair security source untrust destination trust

[FW1-zone-pair-security-Untrust-Trust]packet-filter 2002

[FW1-zone-pair-security-Untrust-Trust]quit

[FW1]

[FW1]zone-pair security source trust destination local

[FW1-zone-pair-security-Trust-Local]packet-filter 2002

[FW1-zone-pair-security-Trust-Local]quit

[FW1]

[FW1]zone-pair security source local destination trust

[FW1-zone-pair-security-Local-Trust]packet-filter 2002

[FW1-zone-pair-security-Local-Trust]quit

[FW1]

[FW1]zone-pair security source untrust destination local

[FW1-zone-pair-security-Untrust-Local]packet-filter 2002

[FW1-zone-pair-security-Untrust-Local]quit

[FW1]

[FW1]zone-pair security source local destination untrust

[FW1-zone-pair-security-Local-Untrust]packet-filter 2002

[FW1-zone-pair-security-Local-Untrust]quit

[FW1]

[FW1]zone-pair security source trust destination trust

[FW1-zone-pair-security-Trust-Trust]packet-filter 2002

[FW1-zone-pair-security-Trust-Trust]quit

[FW1]

[FW1]zone-pair security source untrust destination untrust

[FW1-zone-pair-security-Untrust-Untrust]packet-filter 2002

[FW1-zone-pair-security-Untrust-Untrust]quit

[FW1]int loopback 0

[FW1-LoopBack0]ip address 2.2.2.2 32

[FW1-LoopBack0]quit

[FW1]int gi 1/0/2

[FW1-GigabitEthernet1/0/2]des <connect to R1>

[FW1-GigabitEthernet1/0/2]ip address 10.0.0.2 30

[FW1-GigabitEthernet1/0/2]quit

[FW1]int gi 1/0/3

[FW1-GigabitEthernet1/0/3]des <connect to R2>

[FW1-GigabitEthernet1/0/3]ip address 10.0.0.6 30

[FW1-GigabitEthernet1/0/3]quit

[FW1]security-zone name Trust

[FW1-security-zone-Trust]import interface GigabitEthernet 1/0/2

[FW1-security-zone-Trust]import interface loopback 0

[FW1-security-zone-Trust]quit

[FW1]security-zone name Untrust

[FW1-security-zone-Untrust]import interface GigabitEthernet 1/0/3

[FW1-security-zone-Untrust]quit

[FW1]ip route-static 192.168.1.0 255.255.255.0 10.0.0.1

[FW1]ip route-static 172.16.1.0 255.255.255.0 10.0.0.5