初始化Kubenetes报错2：error execution phase preflight: [preflight] S..

error execution phase preflight: [preflight] Some fatal errors occurred:
        [ERROR Port-6443]: Port 6443 is in use
        [ERROR Port-10251]: Port 10251 is in use
        [ERROR Port-10252]: Port 10252 is in use
        [ERROR FileAvailable--etc-kubernetes-manifests-kube-apiserver.yaml]: /etc/kubernetes/manifests/kube-apiserver.yaml already exists
        [ERROR FileAvailable--etc-kubernetes-manifests-kube-controller-manager.yaml]: /etc/kubernetes/manifests/kube-controller-manager.yaml already exists
...

[root@test2 ~]# kubeadm init --apiserver-advertise-address=192.168.2.129 --image-repository registry.aliyuncs.com/google_containers --kubernetes-version v1.13.3 --service-cidr=10.1.0.0/16 --pod-network-cidr=10.244.0.0/16
[init] Using Kubernetes version: v1.13.3
[preflight] Running pre-flight checks
error execution phase preflight: [preflight] Some fatal errors occurred:
        [ERROR Port-6443]: Port 6443 is in use
        [ERROR Port-10251]: Port 10251 is in use
        [ERROR Port-10252]: Port 10252 is in use
        [ERROR FileAvailable--etc-kubernetes-manifests-kube-apiserver.yaml]: /etc/kubernetes/manifests/kube-apiserver.yaml already exists
        [ERROR FileAvailable--etc-kubernetes-manifests-kube-controller-manager.yaml]: /etc/kubernetes/manifests/kube-controller-manager.yaml already exists
        [ERROR FileAvailable--etc-kubernetes-manifests-kube-scheduler.yaml]: /etc/kubernetes/manifests/kube-scheduler.yaml already exists
        [ERROR FileAvailable--etc-kubernetes-manifests-etcd.yaml]: /etc/kubernetes/manifests/etcd.yaml already exists
        [ERROR Port-10250]: Port 10250 is in use
        [ERROR Port-2379]: Port 2379 is in use
        [ERROR Port-2380]: Port 2380 is in use
        [ERROR DirAvailable--var-lib-etcd]: /var/lib/etcd is not empty
[preflight] If you know what you are doing, you can make a check non-fatal with `--ignore-preflight-errors=...

[root@test2 ~]# kubeadm reset     //重启kubeadm
[reset] WARNING: changes made to this host by 'kubeadm init' or 'kubeadm join' will be reverted.
[reset] are you sure you want to proceed? [y/N]: y    //输入y
[preflight] running pre-flight checks
[reset] Reading configuration from the cluster...
[reset] FYI: You can look at this config file with 'kubectl -n kube-system get cm kubeadm-config -oyaml'
W0717 17:33:41.676764   77512 reset.go:213] [reset] Unable to fetch the kubeadm-config ConfigMap, using etcd pod spec as fallback: failed to get config map: configmaps "kubeadm-config" not found
[reset] stopping the kubelet service
[reset] unmounting mounted directories in "/var/lib/kubelet"
[reset] deleting contents of stateful directories: [/var/lib/etcd /var/lib/kubelet /etc/cni/net.d /var/lib/dockershim /var/run/kubernetes]
[reset] deleting contents of config directories: [/etc/kubernetes/manifests /etc/kubernetes/pki]
[reset] deleting files: [/etc/kubernetes/admin.conf /etc/kubernetes/kubelet.conf /etc/kubernetes/bootstrap-kubelet.conf /etc/kubernetes/controller-manager.conf /etc/kubernetes/scheduler.conf]

The reset process does not reset or clean up iptables rules or IPVS tables.
If you wish to reset iptables, you must do so manually.
For example:
iptables -F && iptables -t nat -F && iptables -t mangle -F && iptables -X

If your cluster was setup to utilize IPVS, run ipvsadm --clear (or similar)
to reset your system's IPVS tables.

[root@test2 ~]# kubeadm init \
--apiserver-advertise-address=192.168.2.129 \
--image-repository registry.aliyuncs.com/google_containers \
--kubernetes-version v1.13.3 \
--service-cidr=10.1.0.0/16 \
--pod-network-cidr=10.244.0.0/16

......
Your Kubernetes master has initialized successfully!

To start using your cluster, you need to run the following as a regular user:

  mkdir -p $HOME/.kube
  sudo cp -i /etc/kubernetes/admin.conf $HOME/.kube/config
  sudo chown $(id -u):$(id -g) $HOME/.kube/config

You should now deploy a pod network to the cluster.
Run "kubectl apply -f [podnetwork].yaml" with one of the options listed at:
  https://kubernetes.io/docs/concepts/cluster-administration/addons/

You can now join any number of machines by running the following on each node
as root:

  kubeadm join 192.168.2.129:6443 --token si974n.v8615659h9x6x4xe --discovery-token-ca-cert-hash sha256:d6d1c5d0290ee0217d14d7d6bdea23b1fc911186e0ea94847a1f52d8ed32761d